HT46R23 DATASHEET PDF

HT46R23 datasheet, HT46R23 circuit, HT46R23 data sheet: HOLTEK – A/D Type 8-Bit MCU,alldatasheet, datasheet, Datasheet search site for Electronic. A/D Type 8-Bit MCU (HT46C23 EOL) The HT46R23/HT46C23 are 8-bit, high performance, RISC architecture microcontroller devices specifically designed for . HT46R23 Datasheet PDF Download – 8-Bit OTP Microcontroller, HT46R23 data sheet.

Author: Daiktilar Dikinos
Country: Mauritania
Language: English (Spanish)
Genre: Medical
Published (Last): 6 January 2014
Pages: 407
PDF File Size: 9.36 Mb
ePub File Size: 3.97 Mb
ISBN: 172-7-51092-934-3
Downloads: 28616
Price: Free* [*Free Regsitration Required]
Uploader: Viktilar

When a control transfer takes place, an additional dummy cycle is required. There are three types of selection: The destination will be. The contents of the data memory remain unchanged.

The lower byte datssheet the program counter PCL is a read- able and writeable register 06H. Instruction fetching and execution are pipelined in bt46r23. This option is to decide if an RC or crystal oscillator is chosen as system clock. Enable or disable LVD function.

HT46R23/HT46C23 – A/D Type 8-Bit MCU

In the transmit mode, the transmitter checks RXAK bit to know datashest receiver which wants to receive Rev. The 0 flag is affected. Otherwise the original instruction cycle is unchanged. The contents of the specified data memory are incremented by 1.

Data of the specified data memory and the carry flag are rotated 1 bit right.

When executing a jump instruction, conditional skip ex. Writing indirectly result in no operation. The registers states are summarized in the following table. Datahseet result is stored in the accumulator. The data is stored in the HDR register. The contents of the specified data memory are copied to the accumulator. The contents of the specified data memory are rotated 1 bit right with bit 0 rotated datasheef bit 7. For the most up-to-date information, please visit our web site at http: T 1 T 2 T ht46d23 T 4 T 1 When executing a jump instruction, conditional skip ex- ecution, loading PCL register, subroutine call, initial re- set, internal interrupt, external interrupt or return from subroutine, the PC manipulates the program transfer by loading the address corresponding to each instruction.

  BHARTI AIRTEL ANNUAL REPORT 2012-13 PDF

However, the pipelining scheme causes each instruc- tion to effectively execute in a cycle. I2C is a trademark of Philips Semiconductors. Data in the specified data memory is decremented by 1.

The contents of the specified data memory and the carry flag are together rotated 1 bit right. The instruction unconditionally calls a subroutine located at the indicated address. The result is stored in the data memory. The contents of the specified data memory are decremented by 1. The system clock is internally divided into four non-overlapping clocks.

The indicated address is then loaded. At nect a pull-high resistor respectively.

The program counter then points to the. For output operation, instructions. This also changes the status register. Data in the specified data memory is decremented by 1, leaving the result in the accumulator. Current program counter bits Rev.

Moving data into the. These are stress datashret only. After a chip reset, the SP will point to the top of the stack. It is particularly suitable for use in products such as washing machine controllers and home appli- ances. After accessing a program memory word to fetch an in.

  ALBERTO VILLOLDO CARTI PDF

The WDT and prescaler are cleared. The destination will be within locations.

HT46R23 datasheet, Pinout ,application circuits HT46R23/HT46C23 – A/D Type 8-Bit MCU

Bit 0 replaces the carry bit; the original carry flag is rotated into the bit 7 position. Taipei Office 11F, No. If an instruction changes the program counter, two cycles are ht46r32 to complete the instruction. Home – IC Supply – Link. In other words, a dummy period will be inserted after wake-up.

When a control transfer takes place, an additional. The timer mode functions as a normal timer with the clock source coming from the fINT clock. In the case of counter overflows, the counter is lower-order byte buffer. The related interrupt request flag the stack. One instruction dagasheet consists of four system clock cycles. Once a wake-up event occurs, it takes tSYS sys- tem clock period to resume normal operation. Some registers remain un- and results in the following If read, the clock will be blocked datasheeet avoid errors.

Start the discussion

Leave a Reply