DATASHEET OF HT12D PDF

HT12D 2 12 Series of Decoders Features. Operating voltage: V~12V Low power and high noise immunity CMOS Built-in oscillator needs only 5% resistor. HT12DDIP Ic-remote Control Decoder Features. Operating voltage: V~12V Low power and high noise immunity CMOS technology Low standby current. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit.

Author: Fenrisar Zuluzshura
Country: Puerto Rico
Language: English (Spanish)
Genre: History
Published (Last): 8 June 2015
Pages: 310
PDF File Size: 2.92 Mb
ePub File Size: 1.75 Mb
ISBN: 345-2-69166-442-7
Downloads: 93932
Price: Free* [*Free Regsitration Required]
Uploader: Taran

We should set the bits in same pattern on Encoder and Decoder IC to pair them. This oscillator can be used by connecting these two pins through a 1M Resistor. A valid transmission in indicated by a high signal at VT pin. The data on 4 bit latch type output pins remain unchanged until new is received.

This IC hasmany applications in short range remote controlling. This IC has a total of 18 pinsnine on either sides: This pin outputs the parallel data serially. Basically found in applications of remote control systems. This is an CMOS logic integrated circuit encoder.

So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. The serial input data is compared with the local addresses three times continuously. An LED can also be connected across this terminal to indicate output.

These are the 8-bit address bits, which is used to protect your data.

ht12e ht12d datasheet – ht12e ht12d datasheet

In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. It is mainly provided to interface RF and infrared circuits. What is Web Browser. Interface Ht2d with Arduino. The Encoded 12 bit output data obtained from HT12E has to be given here.

  BASHUNDHARA CITY RAFFLE DRAW RESULT 2012 PDF

It is not mandatory to use it. The IC has a built in oscillator. It ratasheet very important that your Decoder should have the same address of that of the encoder. Used for interfacing RF circuits generally MegaHz. They can also be connected to LED to physically view the received data.

They are paired with 2 12 series of encoders. This pin will go high when a data is received. Valid transmission; active high. HT12D is capable of decoding 12 bits, of which 8 are address bits and 4 are data bits.

After one complete cycle of data transfer the pin TE goes in high impedance state, thus indicating 1 cycle of data transfer. HT12D is a decoder integrated circuit that belongs to 2 12 series of decoders. Choosing Battery for Robots. This pin powers the IC should hr12d only 5V. Connected to the Ground of ht12e.

HT12D Decoder IC

I am now going to tell you about to control a certain robot wirelessly rather than using wires. Generally a resistor of value 51 KOhms can be used. It decodes the serial addresses and data received by, say, an RF receiver, into parallel data and sends them to output data pins. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an pf of 8-bit has to be set using the pins A0 to A7.

HT12D/HT12F – Product Details – Holtek

To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given here.

  ERISIPELA CELLULITE PDF

By continuing to use this website, you agree to their use.

Skip to main content. Supply voltage; 5V 2. Dstasheet Motor For Robots. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc. TL — Programmable Reference Voltage.

A basic circuit diagram for the HT12D IC is shown below In the above circuit I have set the 8-bit address data as 0b, by connecting all address pins to ground. HT12E IC has four bit parallel data inputwhich it then converts to serial data output. Interface SD Card with Arduino. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded.

If you want security you can connect any of the 8 pins to 5V to make it high. To find out more, darasheet how to control cookies, see here: Skip to content Gone are the days when we used to use wires to connect two devices to establish a communication path. In simple terms, HT12D converts the serial input into parallel outputs. For decoding a data the IC will requires an oscillatorluckily this IC has one in-built.

The input data code is decoded when no error or unmatched codes are found. Dataasheet this helps in setting up oscillations in the IC. Virgin Galactic — Commercial Space Flight.

Start the discussion

Leave a Reply