ATMEL 24C04 PDF

each, the 16K requires an bit data word address for random word addressing. WP Pin. Status. Part of the Array Protected. 24C01A. 24C 24C 24C08A. 24C04 EEPROM are available at Mouser Electronics. Mouser offers For: 24C Obsolete. Microchip Technology / Atmel, EEPROM 7 MILS V – 10MS V. Read about ’24C04 Interfacing issue’ on elementcom. Hey there,I am trying to interface the AT24C04 4K EEPROM with Atmega

Author: Shaktijar Maushicage
Country: Solomon Islands
Language: English (Spanish)
Genre: Literature
Published (Last): 12 January 2005
Pages: 461
PDF File Size: 1.61 Mb
ePub File Size: 3.58 Mb
ISBN: 985-3-55257-146-1
Downloads: 25945
Price: Free* [*Free Regsitration Required]
Uploader: Faudal

When you say that you are “writing” to the pins this does not make clear exactly what you are doing. Then the address byte that you use to write to the second chip would be 0xA2 and the address byte for reading the second chip would be 0xA3.

Can you explain what hardwiring is? By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

Atmel Corporation makes no warranty for the. Atmel Corporation makes no warranty for the use. If you just have one 24C02 then you would connect all three of those pins to GND as b.

You do not write the addresses; you hardwire them. The information in this document is provided in connection with Atmel products. Home Questions Tags Users Unanswered. If a total of eight 24C02’s are used in the design then each of the devices will have these three pins hard strapped in a different combination from the set of b, b, b, b, b, b, b and b.

  CONVEXITY CONUNDRUMS PDF

It will answer to address that was set up before powering up. The device will not respond to the address that is being set dynamically.

10pcs At24c04 24c04 Serial EEPROM Sop-8 ATMEL

This device is not recommended for new designs. Please refer to AT24C08A. Email Required, but never shown. Atjel 6 This output is from I2C scanner. It connects the SOT package pins to the same signal position of the 8 pin DIPmechanical and electrical connections are supported by this adapter.

It considers the value of the A0,A1 and A2 before the power up and sticks to it till reset. I will try in about an hour. So for example you keep A0: Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use 244c04 the website is subject to these policies.

Then when you want to write to the part use an address byte of 0xA0 and when you want to read use an address byte of 0xA1.

10pcs At24c04 24c04 Serial EEPROM Sop-8 ATMEL | eBay

Is there something else I need to do? The Company assumes no. Post as a guest Name. Also be aware that the A0 to A2 pins on the device package are meant to remain static in a design.

Normally there is no writing to the 24C02 pins. No abstract text available Text: TurboJ The chip says the following: Are you being confused by the common mistake that many people make where they treat the address of an I 2 C wrongly?

Even the data sheet that you linked can lead to confusion in this regard. Sign up using Email and Password. Full 2K Array 24C04 atmeel. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service.

  GODDESS ADBC 3 PDF

Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in. Instead the three bits that you supply out on the interface in the device address field must match the hard strapped values on the pins in order for the device to be selected.

Can you give more information?

However, it doesn’t matter what I set these pins to. Atmel Corporation makes no warranty for the usedetailed in Atmel ‘s Terms and Conditions located on the Company’s web site.

But my suggestion would to directly connect them to ground or VCC for the addressing scheme. Can’t change the values dynamically. The information in this document is provided in connection with Atmel. atmmel

Check your chips markings. Sign up using Facebook. On top of that I have never been sure that it is even possible to dynamically change the strapped value on the A0, A1 and A2 pins of a 24C02 after it has powered up. Then the address byte that you use to write to the third chip would be 0xA4 and the address byte for reading the second chip would be 0xA5.

Found 8 device s. Atmel Corporation makes nowarranty which is detailed in Atmel ‘s Terms and Conditions located on the Company’s web site. RoomJapan Atmel Japan K.

Start the discussion

Leave a Reply