ASTM F146 PDF

F – 80 Standard Test Methods for Fluid Resistance Of Gasket Materials. Designation: F – Standard Test Methods for. Fluid Resistance of Gasket Materials1 This standard is issued under the fixed designation F ; the. ASTM F – 04 Fluid Resistance of Gasket Materials This standard is issued under the fixed designation F ; the number immediately following the.

Author: Karr Shaktikree
Country: France
Language: English (Spanish)
Genre: History
Published (Last): 22 February 2011
Pages: 195
PDF File Size: 4.55 Mb
ePub File Size: 20.44 Mb
ISBN: 565-9-14574-605-2
Downloads: 46703
Price: Free* [*Free Regsitration Required]
Uploader: Samulkree

Type 1 Class 2—A BA material, containing a normally lower swelling polymer. Other physical property tests described in this standard are not applicable for these materials. Precision and Bias 7 The specific test fluids and test conditions outlined were selected as typical for purposes of comparing different materials and can be used as a routine test when agreed upon between the purchaser and the manufacturer.

Dead weight loads are listed asmt Table f416.

ASTM F 146 – 04

Size px x x x x We need your help! Use enough fluid to provide a minimum of 10 mL for each specimen in the container. The results of these test methods are not intended to give any direct correlation with service conditions in view of the wide variations in temperature and special uses encountered in gasket applications. Historical Version s – view previous versions of standard. A number in parentheses indicates the year of last reapproval.

Please copy and paste this embed script to where you want to embed Embed Script. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Last previous edition approved in as F — ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Change the distilled water used in the test frequently. The user should be aware v146 results may differ. The change in thickness of the specimens is to be calculated as an expression of percentage change from the original thickness.

  KANAANISCHE UND ARAMISCHE INSCHRIFTEN PDF

F — 04 Standard Test Methods for Fluid Resistance of Gasket Materials1 This standard is issued under the fixed designation F ; the number immediately following the designation indicates the year of original adoption or, in the case qstm revision, the year of last revision. There were six Type 1,7, three Type 3, and one Type 5 material evaluated for immersion weight change and thickness change in IRM oil.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. astj

Insert the aluminum-foil covered stoppers into the test tubes before placing them in the supporting rack within the oven. The anvil shall have a diameter not less than that of the presser xstm, which has a diameter of 6. We are a non-profit group that run this aztm to share documents.

Graduate the dial in 0. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Take a sufficient number of readings, depending on the size of the specimen, to provide a reliable average value.

ASTM F – 04 – Free Download PDF

A superscript epsilon e indicates an editorial change since the last revision or reapproval. Please fill this form, we will try to respond as soon as possible. ICS Number Code BoxTrenton, NJ Current edition approved April 1, The inch-pound units in parentheses are for asstm only.

We need your help to maintenance this website.

Please help us to share our service with your friends. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. It is designed for testing specimens cut from gasketing materials or from finished articles of commerce.

Temperature of Test Measurement 7. This standard has been approved for use by agencies of the Department of Defense. Pour enough fresh test fluid over the specimens to ensure that the specimens are wetted and covered by the fluid. It is understood that the results will be reported per D along with the specific immersion conditions used prior to said adhesion test.

  BOTF MANUAL PDF

NOTE 2—Great care must be taken to record the swollen thickness when the needle slows to a different rate which reflects indentation into the softened specimen. It is designed aastm testing specimens cut from gasketing materials or from finished articles of commerce. This gives the final volume, V2. Use the same sinker throughout.

ASTM F146 – 12

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Pour enough fresh fluid into the tube to completely cover the specimens and ensure that they are immersed. If such information is not available, then the material should be tested by itself in fresh fluid to determine compatibility with said fluid. These test methods are applicable to ethylene glycol, propylene glycol, commercial coolants and blends with water thereof see Note ast,water, and other commercial oils and fuels.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. These test methods are not applicable to the testing of vulcanized rubber, a procedure that is described in Test Method D Link to Active This link will always route to the current Active version of the standard.

These test f1146 are not applicable to the testing of vulcanized rubber, a procedure that is described in Test Method D

Start the discussion

Leave a Reply